• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they are not susceptible to rust or rot.

It is crucial to wash and oil UPVC windows and doors regularly. This will reduce costly repairs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause serious damage to your home and even be fatal. You should take the time to make sure that your windows are in good condition.

For single pane windows it can be relatively simple to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. However, if you have double-pane windows that are held in place by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this situation you'll need locate some plastic spacers that will assist the new pane to fit perfectly into the frame of the window.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth prior to when you start working on the glass, so that any shards will fall onto the cloth rather than on the floor where they could be trodden under and cause further damage.

It's a great idea to cover the gap with tape after the glass has been removed. This will stop drafts and water from getting into your property until a professional arrives to repair the window. It also acts as a barrier that will prevent any intruders to gain access to your home. If the distance between the window and the door is substantial, you may need to consider an alarm system that includes windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. However, over time, they may be afflicted by a variety of problems including sliding. A sagging window in uPVC can cause issues with light, draughts and even security. It's important to take action immediately if you notice your upvc window Repair windows are sagging.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll need to open the window to get to the frame. Then, using the screwdriver, you'll be able to remove the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you've moved your hinges. If you're satisfied with the size of the window, tighten the screws to secure them in place.

If you are unable to reposition the hinges, you may require replacing the seal. Rubber seals may dry out and lose their elasticity with time, causing them to loosen. If this happens, it's essential to replace the seal as fast as possible to ensure your uPVC windows are waterproof and secure from draughts.

uPVC handles can also loosen up. This is typically caused by screws that have become undone over time, but it could be caused by the handle mechanism wears out. Luckily, it's not difficult to fix the loose uPVC window handle yourself. You'll first need to close the window and do an initial fitting. The joint at the corner of the sash should be aligned with the joint on the casing. If it does not then you can use the screwdriver to loosen the handle. Then, you can turn the mechanism into position.

3. Water Leaks

If you wake up to wet floors and damp walls each time it rains, it is important that you take action. Windows that leak water do can not only cause degradation of your home's structure but also hinder your efforts to regulate the temperature in your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on how severe the problem is, the old caulking may have to be removed. It is essential to keep in mind that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk and then make the area more difficult to clean and can decrease the efficiency of your energy usage.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more serious cases you might have to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the home.

It is also important to remember that if the leak originates from the glass in your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and open with ease, it may be hinges that are at fault. They can be easily replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical part hinges will be damaged over time. The process of replacing a hinge on a window is essentially a simple process but it can be easier with someone else to help you hold the frame in place.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. This can be done by looking for the arrows on each hinge. This indicates which way the window should open.

The issue can be caused either due to opening the window in the wrong way or a faulty installation at the factory. Sending us a picture via our website is often enough to solve the issue. We are happy to give advice.

It is also crucial to lubricate the hinges on a regular basis. This can be accomplished by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window operate and close more easily. It can also stop corrosion and reduce the possibility of sticking. Ideally, you should do this once a year. WD40 or other solvent-based oils are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. Firstly the hinges, again due to wear and tear could become misaligned. This will cause gaps to develop where the sash meets the frame. If they are beyond repair, it may be necessary to have them realigned. The interlock may be unbalanced. This is located on the hinge's side, and might require to be cleaned. In some instances it is possible to replace these.

The second most frequent cause of draughts is the window seals, these are prone to wear or damaged over time, and let air escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glasses. This will help regulate indoor temperatures and decrease the possibility of draughts.

One of the most effective ways to reduce drafts is to use a draught excluder. These are typically fabric tubes which are filled with a type of filler. They can be put on top of your windowsill. They will keep your home warm by blocking out cold air.

With a little regular maintenance and repairs your windows made of upvc will continue to provide a great level of security and insulation for your home. However, it is important to recognise that windows last for a certain period of time and there may come an point at which it is more economical to replace them than fix them. If you have any problems with your upvc window you should consult a professional as soon as you can.